BS 1900:1976 副基準溫度計規范

Series of 29 total immersion thermometers for checking the accuracy of other thermometers in the range -80C to 505C. Materials, essential

Specification for secondary reference thermometers

ASTM E1502-16 基準溫度凍結點室的使用

5.1 A pure material has a well defined phase transition

Standard Guide for Use of Fixed-Point Cells for Reference Temperatures

ASTM E1502-98(2003)e1 基準溫度凍結點室的使用

1.1 This guide describes the essential features of freezing-point cells and auxiliary apparatus, and the techniques required to realize freezing

Standard Guide for Use of Freezing-Point Cells for Reference Temperatures

CNS 14939-2005 柏油體積校正至基準溫度計算法

本標準規定各類柏油(瀝青)在-25至+275 ℃間測定之體積轉換成基準溫度15 ℃體積校正值及換算系數表，惟不適用于乳化瀝青

Standard practice for determining asphalt volume correction to a base temperature

ASTM E1502-10 供基準溫度冰點室使用的標準指南

A pure material has a well-defined phase transition behavior, and the phase transition plateau, a characteristic of the material, can serve

Standard Guide for Use of Freezing-Point Cells for Reference Temperatures

ASTM E1502-22 基準溫度用固定點電池的使用標準指南

1.1 This guide describes the essential features of fixed-point cells and auxiliary apparatus, and the techniques required to realize fixed points

Standard Guide for Use of Fixed-Point Cells for Reference Temperatures

KS M ISO 91-2-2008(2018 石油計量表第2部分:基于20℃基準溫度的表

Petroleum measurement tables－Part 2：Tables based on a reference temperature of 20℃

ASTM D4311/D4311M-09 基準溫度下瀝青體積校正的標準試驗方法

Asphalts change in volume with change in temperature. They are loaded or transferred at widely varying temperatures. Volume correction factors

Standard Practice for Determining Asphalt Volume Correction to a Base Temperature

MIL MIL-S-19500/335-1965 半導體器件 硅 電壓基準（溫度穩定）類型 1N430A 1N430B

SEMICONDUCTOR DEVICE, SILICON, VOLTAGE REFERENCE (TEMPERATURE-STABLE) TYPE 1N430A, 1N430B

ASHRAE LV-11-021-2011 估算任何基準溫度下供暖和制冷度日的方法

ABSTRACT This paper examines several methods for calculating heating and cooling degree-days to any base by relying on temperature statistics

Methods for Estimating Heating and Cooling Degree-Days to Any Base Temperature

ASTM D4311/D4311M-15 測定調整到基準溫度時瀝青體積的標準實踐規程

3.1 Asphalts change in volume with change

Standard Practice for Determining Asphalt Volume Correction to a Base Temperature

ASTM D4311-96 調整到基準溫度時瀝青體積測定的標準實施規程

1.1 This practice provides tables of volume correction factors which may be used to convert volumes of asphalt measured at different temperatures

Standard Practice for Determining Asphalt Volume Correction to a Base Temperature

ASTM E1921-97 測定碳素體鋼在轉變范圍內基準溫度的標準試驗方法

1.1 This test method covers the determination of a reference temperature, To, which characterizes the fracture toughness

Standard Test Method for Determination of Reference Temperature, T_o, for Ferritic Steels in the Transition Range

ASTM E1921-16 測定碳素體鋼在轉變范圍內基準溫度的標準試驗方法

5.1 Fracture toughness is expressed in terms

Standard Test Method for Determination of Reference Temperature, To, for Ferritic Steels in the Transition Range

ASTM E1921-10 測定碳素體鋼在轉變范圍內基準溫度的標準試驗方法

Fracture toughness is expressed in terms of an elastic-plastic stress intensity factor, KJc

Standard Test Method for Determination of Reference Temperature, T_o, for Ferritic Steels in the Transition Range