ISO 6443:2005 門扇.高度、寬度、厚度和方正度

This European standard applies to all rectangular door leaves and the measurable parameters of doors of other shapes. This standard specifies

Door leaves - Method for measurement of height, width, thickness and squareness

EN 1529:1999 門扇.高度,寬度,厚度和方度.公差級

This standard givesThe tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies to door

Doors leaves - Height, width, thickness and squareness - Tolerance classes

MSZ 2830-1980 鋼管的弧度90度－180度

The arc of the steel pipe is 90 degrees - 180 degrees

BS 3715:1964 濃度梯度密度柱規范

Specifies requirements for the columns and their calibration, and provides a method for determining the apparent density of floats and recommends

Specification for concentration gradient density columns

ASTM E140-97e2 金屬標準硬度換算表布氏硬度、維氏硬度、洛氏硬度、表面硬度、努氏硬度和硬度計硬度的關系

Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness

ANSI/ATIS 0600010-2014 溫度、濕度和高度標準

Temperature, Humidity, & Altitude Standards

CECS 278-2010 剪壓法檢測混凝土抗壓強度技術規程

本規程適用于截面具有直角邊、可施加剪壓力的結構混凝土抗壓強度(以下簡稱混凝土強度)的檢測。 當對結構中混凝土強度有檢測要求時,可按本規程進行檢測,并推定混凝土強度,檢測結果可作為處理混凝土強度問題的依據。 本規程不適用于表層與內部質量有明顯差異或內部存在缺陷的結構混凝土強度的檢測

Technical specification for testing of concrete compressive strength by shear-pressure method

BS EN 1529:2000 門扇.長度,寬度,厚度和方度.公差等級

This standard gives the tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies

Door leaves - Height, width, thickness and squareness - Tolerance classes

JTG/T D65-04-2007 公路涵洞設計細則

本細則適用于新建和改建各級公路涵洞的勘測設計

Guidelines for Design of Highway culvert

SS-EN 1529:2021 門板 高度、寬度、厚度和方度 公差等級

This document gives the tolerance limits for specified dimensions of height, width and thickness, and for squareness of door leaves. It applies

Door leaves - Height, width, thickness and squareness - Tolerance classes

AS 1377.1:1973 換算表 長度、角度和速度

Conversion tables - Length, angle and velocity

DIN EN 951:1999-05 門扇高度、寬度、厚度和方形度的測量方法

Door leaves - Method for measurement of height, width, thickness and squareness; German version EN 951:1998

DIN EN 1529:2022-02 門扇 高度、寬度、厚度和方形度 公差等級

Dieses Dokument legt die Toleranzgrenzen zu den vereinbarten Abmessungen von H?he, Breite und Dicke sowie zur Rechtwinkligkeit von Türbl?ttern fest

Door leaves - Height, width, thickness and squareness - Tolerance classes; German version EN 1529:2021

NF P20-606*NF EN 1529:2021 門扇 高度、寬度、厚度和垂直度 公差等級

Door leaves - Height, width, thickness and squareness - Tolerance classes

RAPPORT BT.484-2 FRENCH-1986 亮度幅度/同步幅度的關系

RATIO OF PICTURE-SIGNAL TO SYNCHRONIZING-SIGNAL