ASTM D8290-20 用中紅外激光光譜法測定航空渦輪燃料中脂肪酸甲酯（FAME）的標準試驗方法

1.1 This test method covers the quantification of the fatty acid methyl esters (FAME) content in aviation turbine fuel in the range of 10 mg ?kg

Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Aviation Turbine Fuel using Mid-Infrared Laser Spectroscopy

NASM1312-20-1997 緊固件測試方法；方法 20 單剪

Applicability. This test method outlines the procedure and apparatus for testing fasteners in single shear

Fastener Test Methods; Method 20 Single Shear

AIA NASM1312-20-1997 緊固件測試方法；方法 20 單剪 FSC 53GP

Fastener Test Methods; Method 20 Single Shear FSC 53GP

EIA-448-20-1989 方法 20 機電元件測試方法 鏡頭表面接觸溫度測試方法

PURPOSE The purpose of this test method is to determine whether the switch lens face meets the touch temperature (rise above ambient requirements

Method 20 Test Method for Electromechanical Components Test Method for Lens Face Touch Temperature

ECA EIA-448-20-1989 方法20.機電元件的測試方法.透鏡面接觸溫度的測試方法

Method 20 Test Method for Electromechanical Components Test Method for Lens Face Touch Temperature

GJB 3405-1998 20~1000MHz屏蔽室場分布測試方法

20~1000MHz shielded room field distribution test method

LST EN 60695-11-20-2000 火災隱患測試 第 11-20 部分：測試火焰 500 W 火焰測試方法（IEC 60695-11-20:1999）

Fire hazard testing. Part 11-20: Test flames. 500 W flame test methods (IEC 60695-11-20:1999)

09/30206613 DC BS EN 60695-11-20 火災危險測試 第11-20部分 測試火焰 500 W 火焰測試方法

Cross References: IEC 60695-11-5:2004 IEC 60695-11-3:2004 IEC Guide 104:1997 ISO/IEC Guide 51:1999 ISO 291:1997 ISO 293:1986 ISO 294:1996

BS EN 60695-11-20. Fire hazard testing. Part 11-20. Test flames. 500 W flame test methods

NASM1312-20-2016 緊固件測試方法 方法 20 單剪切（修訂版 2）

Applicability. This test method outlines the procedure and apparatus for testing fasteners in single shear. While this method primarily is for testing

FASTENER TEST METHODS@ METHOD 20@ SINGLE SHEAR (Rev 2)

AIA/NAS NASM1312-20-2011 緊固件測試方法 方法 20 單剪切（修訂版 1）

FASTENER TEST METHODS METHOD 20 SINGLE SHEAR (Rev 1)

NASM1312-20-2011 緊固件測試方法 方法 20 單剪切（修訂版 1）

Applicability. This test method outlines the procedure and apparatus for testing fasteners in single shear. While this method primarily is for testing

FASTENER TEST METHODS METHOD 20 SINGLE SHEAR (Rev 1)

GB/T 13216.5-1991 甘油試驗方法 20℃時密度的測定

本標準規定了甘油20℃時的密度測定法

Test methods for glycerines--Determination of density at 20℃

AIA/NAS NASM1312-20-2016 緊固件測試方法，方法 20，單剪切（修訂版 2）

FASTENER TEST METHODS, METHOD 20, SINGLE SHEAR (Rev 2)

LST EN 60695-11-20-2000/A1-2003 火災隱患測試 第 11-20 部分：測試火焰 500 W 火焰測試方法（IEC 60695-11-20:1999/A1:2003）

Fire hazard testing. Part 11-20: Test flames. 500 W flame test methods (IEC 60695-11-20:1999/A1:2003)

ANSI/TIA-455-176-B-2020 IEC-60793-1-20 光纖 第 1-20 部分：測量方法和測試程序 光纖幾何

IEC-60793-1-20 Optical Fibres - Part 1-20: Measurement Methods and Test Procedures- Fibre Geometry