共找到 150 條與 瀝青橡膠罩面密封 相關(guān)的標準，共 10 頁
This European Standard describes a method for preparing asphalt blocks intended for testing of joint sealants according to prEN 13880-7 and prEN
Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements; German version EN 13880-11:2003
SWITCH SUBASSEMBLY, BOOT, DRIPPROOF PANEL SEAL (FOR ILLUMINATED PUSH BUTTON SWITCH) (SUPERSEDING MIL-S-22885/13G) (S/S BY MIL-PRF-22885/13J)
Cross References: ISO 37 ISO 48:2007 ISO 188 ISO 815-1 ISO 815-2 ISO 1431-1 ISO 1817 ISO 2230 ISO 2285 ISO 3302-1:1996/Amd 1:2001 ISO
BS ISO 4635. Rubber, vulcanized. Preformed joint seals for use between concrete highway paving sections. Specification
This specification covers a silicone, electrically conductive and corrosion-inhibiting sealing compound. This sealing compound has been used typically
Sealing Compound, Silicon Rubber, Two-Part, Electrically Conductive and Corrosion Resistant (Nonchromated) for Use from -67 to 500 Degrees F (-55 to 260 Degrees C)
Fittings with ball sleeve, stud type with O-ring face seal. Construction
The blister test is used to determine the interfacial fracture energy (IFE) of hot-poured asphalt crack sealant at the application temperature
Standard Method of Test for Measuring Interfacial Fracture Energy of Hot-Poured Asphalt Crack Sealant Using a Blister Test
The blister test is used to determine the interfacial fracture energy (IFE) of hot-poured asphalt crack sealant at the application temperature
Standard Method of Test for Measuring Interfacial Fracture Energy of Hot-Poured Asphalt Crack Sealant Using a Blister Test
The blister test is used to determine the interfacial fracture energy (IFE) of hot-poured asphalt crack sealant at the application temperature
Standard Method of Test for Measuring Interfacial Fracture Energy of Hot-Poured Asphalt Crack Sealant Using a Blister Test
Hot-applied joint sealants - Part 11: test method for the preparation of asphalt blocks intended for functional testing and for the determination of compatibility with bituminous coatings
3.1 These test methods describe procedures
Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements
This European Standard describes a method for preparing asphalt vlocks intended for testing of joint sealants according to phEN 12880-7 and EN
Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements
BOOT, DUST AND WATER SEAL, TYPE D(FOR LEVER OPERATED CIRCUIT BREAKERS), STYLE 2 (PANEL MOUNTED COMPLETE WITH MOUNTING FRAME) (SUPERSEDING MIL-B-5423/14D)
This document establishes standard gland dimensions for low pressure static radial O-ring seal applications and provides recommendations for modifying
Gland Design, Elastomeric O-Ring Seals, Static Radial and Face 800 psi Maximum Service
RUBBER VULCANIZED. PREFORMED COMPRESSION SEALS FOR USE BETWEEN CONCRETE MOTORWAY PAVING SECTIONS. SPECIFICATION FOR MATERIAL.
This European Standard describes a method for preparing asphalt blocks intended for testing of joint sealants according to prEN 13880-7 and EN
Hot applied joint sealants - Part 11: Test method for the preparation of asphalt test blocks used in the function test and for the determination of compatibility with asphalt pavements
