ASTM E2918-18 熱機械分析儀性能驗證的標準試驗方法

1.1 This test method provides procedures for validating temperature and length change measurements of thermomechanical analyzers (TMA) and analytical

Standard Test Method for Performance Validation of Thermomechanical Analyzers

ASTM E2918-18 熱機械分析儀性能驗證的標準試驗方法

Standard Test Method for Performance Validation of Thermomechanical Analyzers

ASTM E1363-18 熱機械分析儀溫度校準的標準試驗方法

1.1 This test method describes the temperature calibration of thermomechanical analyzers from ?50 °C to 1500 °C. (See Note 1.) 1.2 The values stated

Standard Test Method for Temperature Calibration of Thermomechanical Analyzers

ASTM E2918-23 熱機械分析儀性能驗證的標準試驗方法

1.1 This test method provides procedures for validating temperature and length change measurements of thermomechanical analyzers (TMA) and analytical

Standard Test Method for Performance Validation of Thermomechanical Analyzers

GB/T 11998-1989 塑料玻璃化溫度測定方法 熱機械分析法

本標準規定了用熱機械分析法測量塑料玻璃化溫度試驗方法。 本標準適用于無定形熱塑性塑料，亦適用于部分結晶的熱塑性塑料，不適用于高填充無定型熱塑性塑料體系。 本標準規定的試驗方法所測得的結果與用其他方法測得的結果，不能相比較

Determination of glass transition temperature of plastics--Thermomechanical analysis

ASTM E1363-08 熱機械分析儀溫度校準的標準試驗方法

Thermomechanical analyzers are employed in their various modes of operation (penetration, expansion, flexure, etc.) to characterize a wide range

Standard Test Method for Temperature Calibration of Thermomechanical Analyzers

SAE J1739-2002 設計中潛在故障模式和效果分析(設計 FMEA)、制造和組裝過程中的潛在故障模式和效果分析(過程 FMEA)以及機械的潛在故障模式和效果分析(機械 FMEA)

This SAE Recommended Practice was jointly developed by DaimlerChrysler Corporation, Ford Motor Company and General Motors Corporation. This document

Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA), and Potential Failure Mode and Effects Analysis for Machinery (Machinery FMEA)

22/30427381 DC BS ISO 11359-1 塑料 熱機械分析（TMA） 第1部分：一般原則

BS ISO 11359-1. Plastics. Thermomechanical analysis (TMA). Part 1. General principles

GB/T 36800.3-2025 塑料 熱機械分析法（TMA） 第3部分：針入溫度的測定

Thermomechanical analysis of plastics (TMA) - Part 3: Determination of needle penetration temperature

VDI 3822 Blatt 2.2.5-2014 損壞分析 彈性體產品因機械應力而損壞

Anwendungsbereich Diese Richtlinie gilt nur f??r solche Sch?den@ die unmittelbar durch mechanische Beanspruchung@ das hei?t aufgrund von

Failure Analysis - Defects on elastomeric products caused by mechanical stress

ASTM E2918-13 熱機械分析儀性能驗證的標準試驗方法

5.1 This test method may be used to determine and validate the performance of a particular

Standard Test Method for Performance Validation of Thermomechanical Analyzers

SAE J1739_200006 設計中的潛在失效模式和影響分析（設計Fmea）、制造和裝配過程中的潛在失效模式和影響分析（工藝Fmea）、機械潛在失效模式和影響分析（機械Fmea）

Potential Failure Mode and Effects Analysis in Design (Design FMEA) and Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) Reference Manual

GOST R 56723-2015 塑料. 熱機械分析法 (TMA). 第3部分. 滲透溫度的測定

Plastics. Thermomechanical analysis (TMA). Part 3. Determination of penetration temperature

ASTM E1867-22 動態機械分析儀溫度校準的標準試驗方法

1.1 These test methods describe the temperature calibration of dynamic mechanical analyzers (DMA) from –100 °C to 300 °C. 1.2 The values stated in SI

Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers

ASTM D5444-24 提取骨料的機械尺寸分析的標準試驗方法

1.1 ?This test method covers a procedure for determination of the particle size distribution of fine and coarse aggregates extracted from asphalt

Standard Test Method for Mechanical Size Analysis of Extracted Aggregate