共找到 125 條與 燃料電池電動汽車 相關的標準，共 9 頁
本文件規定了燃料電池電動汽車車載供氫系統振動試驗的技術要求、設備要求及試驗方法。 本文件適用于工作壓力不超過70MPa、整體框架式、包含單個或多個壓縮氫氣儲存瓶的燃料電池電動汽車的車載供氫系統
Technical requirements for vibration test of on board hydrogen supply system of fuel cell electric vehicle
Full-time service, control and big data management specifications for automotive hydrogen fuel cells
本文件適用于貯存介質為壓縮氫氣、公稱工作壓力不超過70 MPa、工作溫度不低于-40℃且不高于85℃的儲氫氣瓶及其附件組成的燃料電池電動汽車車載供氫系統
Technical specifications for gas replacement of hydrogen supply systems on fuel cell electric vehicles
ISO 23273:2013 specifies the essential requirements for fuel cell vehicles (FCV) with respect to the protection of persons and the environment inside
Fuel cell road vehicles - Safety specifications - Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen (ISO 23273:2013, IDT)
This recommended practice is intended to serve as a procedure to verify the functional performance, design specifications or vendor claims of any PEM
Recommended Practice for Testing Performance of PEM Fuel Cell Stack Sub-system for Automotive Applications
本文件規定了質子交換膜燃料電池膜電極技術要求及測試方法 本文件適用于汽車用質子交換膜燃料電池膜電極
Technical requirements and test methods for membrane electrodes of proton exchange membrane fuel cells for automobiles
4 減排量評估過程 4.1 概述 4.2 邊界及排放源識別 4.3 溫室氣體種類確定 4.4 項目及基準線情景制定 4.5 減排量計算 4.6 監測和數據質量管理 4.7 減排量評估
Technical specifications for greenhouse gas emission reduction for hydrogen fuel cell vehicle project
本標準規定了采用中紅外激光光譜法測定質子交換膜燃料電池（PEMFC）汽車用燃料氫氣中痕量一氧化碳的術語和定義、方法原理、對儀器的一般要求、試驗步驟、結果處理和報告。本標準適用于燃料氫氣中一氧化碳體積分?jǐn)?shù)含量為10×10-9～100×10-6（10 ppb～100 ppm）的的測定
Determination of Trace Carbon Monoxide in Hydrogen Fuel - The Method of Mid-infrared Laser Spectroscopy for PEMFC
本文件規定了新能源汽車燃料電池空壓機電機用冷軋無取向電工鋼帶（片）的、符號與牌號、訂貨內容、一般要求、技術要求、檢驗和試驗、復驗與判定規則、包裝、標志及質量證明書。 本文件適用于制造新能源汽車燃料電池空壓機電機用公稱厚度0.03 mm~0.20mm的冷軋晶粒無取向電工鋼帶（片）[以下簡稱
Cold-rolled non-oriented electrical steel strip (sheet) for new energy vehicle fuel cell air compressor motor
本文件規定了新能源汽車燃料電池空壓機電機用冷軋無取向電工鋼帶（片）的、符號與牌號、訂貨內容、一般要求、技術要求、檢驗和試驗、復驗與判定規則、包裝、標志及質量證明書。 本文件適用于制造新能源汽車燃料電池空壓機電機用公稱厚度0.03 mm~0.20mm的冷軋晶粒無取向電工鋼帶（片）[以下簡稱
Cold-rolled non-oriented electrical steel strip (sheet) for new energy vehicle fuel cell air compressor motor
This recommended practice is intended to serve as a procedure to verify the functional performance, design specifications or vendor claims of any PEM
Recommended Practice for Testing Performance of PEM Fuel Cell Stack Sub-system for Automotive Applications
Recommended Practice for Testing Performance of PEM Fuel Cell Stack Sub-system for Automotive Applications
本文件規定了燃料電池電動汽車車載供氫系統氣密性檢測和置換的術語和定義、技術要求、檢測方法和檢測報告。本文件適用于公稱工作壓力不超過70 MPa、貯存介質為壓縮氫氣、工作溫度不低于-40°C且不高于85°C的儲氫氣瓶及其附件組成的氫燃料電池電動汽車車載供氫系統
Technical requirements for gas tightness detection and substitution of onboard hydrogen supply system of fuel cell electric vehicle
Recommended Practice for Testing Performance of PEM Fuel Cell Stack Sub-system for Automotive Applications
Determination of hydrogen, helium, argon, nitrogen and hydrocarbons for proton exchange membrane fuel cell vehicles - Gas chromatography
