共找到 150 條與 環余熱強度 相關的標準，共 10 頁
Nitrocellulose. Method for determination of mass fraction of residual spirit
本標準規定了循環水供熱原理和注意事項、熱電廠循環水供熱機組的運行技術參數及配備設備性能參數、循環水供熱投入步驟、循環水供熱解列步驟、循環水供熱機組事故處理、調峰站設備的操作步驟。本標準適用于地方小型熱電廠循環水供熱機組（型號為C12-50/10的抽凝式機組
Technical specification for steam turbine circulating water waste heat heating
本標準規定了低溫余熱雙循環發電裝置的術語和定義、型式和基本參數、要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存。本標準適用于利用 60°C~200°C 溫度范圍內的余熱進行發電的低溫余熱雙循環發電裝置（以下簡稱“裝置
Bi-circulation power generation unit for low-temperature waste heat recovery
This document is intended solely for the purpose of providing guidance in the evaluation of metal loss in pressurized pipelines and piping systems
Manual for Determining the Remaining Strength of Corroded Pipelines (B31G - 2012)
This document is intended solely for the purpose of providing guidance in the evaluation of metal loss in pressurized pipelines and piping systems
Manual for Determining the Remaining Strength of Corroded Pipelines
本文件旨在為評估加壓管道和管道系統中的金屬損失提供指導。適用于所有屬于ASME B31壓力管道規范范圍內的管道和管道系統，包括：ASME B31.4（液態碳?xì)浠衔锖推渌后w的管道輸送系統）、ASME B31.8（氣體輸送和分配管道系統）、ASME B31.11（漿料輸送管道系統）以及ASME
Manual for Determining the Remaining Strength of Corroded Pipelines
本文件旨在為評估加壓管道和管道系統中的金屬損失提供指導。適用于ASME B31壓力管道規范范圍內的所有管道和管道系統，包括：ASME B31.4（液態碳?xì)浠衔锖推渌后w的管道輸送系統）、ASME B31.8（氣體輸送和分配管道系統）、ASME B31.11（漿料輸送管道系統）和ASME
Manual for Determining the Remaining Strength of Corroded Pipelines
Reheater Boiler Energy Efficiency and Environmental Protection Testing Methods
This test method covers the determination of the failure characteristics of reinforced plastic pipe when subjected to cyclic internal hydraulic
Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
This specification covers epoxy-resin-impregnated glass laminates in the form of sheets clad on one or both sides with electrolytic copper foil
Plastic Sheet, Copper Faced Glass Fabric Reinforced Epoxy Resin Hot Strength Retention
本標準規定了在輾環機上軋制生產的結構鋼、工具鋼、不銹鋼、耐熱鋼、高溫合金、鈦合金、銅合金、鋁合金熱軋環形件的機械加工余量及公差。 本標準適用于輾環機生產的最大外徑尺寸不大于ф5500mm，最小內徑尺寸不小于最大外尺寸的1/2，最大高度尺寸不大于700mm的熱軋環形件機械加工余量及公差的制定
Machining allowance & tolerance for rolled ring
The Influence of Residual Stress on the Strength of Structural Members
"Concerned primarily with the stability of ""as-delivered@'' rolled@ structural steel shapes of the I or WF type@ this discussion considers
THE INFLUENCE OF RESIDUAL STRESS ON THE STRENGTH OF STRUCTURAL MEMBERS
La presente norma è la versione ufficiale in lingua inglese della norma europea EN ISO 8895 (edizione giugno 2006). La norma specifica un metodo
Shaped insulating refractory products - Determination of cold crushing strength
Evaluation Method for Residual Strength of Oil and Gas Pipelines Containing Defects
