共找到 150 條與 電痕化 相關的標準，共 10 頁
本文件描述了固體絕緣材料耐電痕化和相比電痕化指數的測量方法,適用于交流電壓下使用的設備元件和盤狀材料。 本文件提供了按照要求測定電蝕損的程序。 注1:耐電痕化指數的測量可作為材料的驗收標準,也可作為對材料及零部件進行質量控制的方法。 相比電痕化指數主要可用作材料的基本特性表征和性能比較的參數。 本文
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
本標準規定了固體絕緣材料耐電痕化和相比電痕化指數的測量方法,適用于設備元件和盤狀材料使用交變電壓的場合、本標準規定了按要求進行蝕損的測量、試驗結果不能直接用于估計電氣設備設計時安全爬電距離
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
本試驗方法可測量在電壓最高達600V時固體電氣絕緣材料在電場作用下表面暴露于含雜質的水時的相對耐電痕化性能。 當將電壓施加到放在材料表面上規定的電極裝置之間，且電解液以規定的時間間隔滴到兩電極之間時，在此試驗情況下可能產生電痕化。引起材料破壞所必需的液滴數隨著施加電壓的減少而增加
Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
該標準規定了電氣絕緣材料在電痕化條件下表面性能的測試方法。適用于各種類型的固定態絕緣材料
Method for determining the resistance to tracking of electrical insulating materials, Method KA
本標準樣品是大小為 60 mm×60 mm×3 mm的塑料樣片，每包5片，非試驗面貼有序號
The Qualitative Reference Materials of Tracking Resistance Test (600V) for Electric and Electronic Products
本標準規定了在潮濕條件下測定固體絕緣材料的耐電痕化性試驗方法
Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
Specification for electric luminaires (lighting fittings). General requirements and tests-Resistance to heat, fire and tracking
本標準規定了對受到液態污染物間歇作用且同時表面承受交流電應力的絕緣材料進行性能對比的試驗方法。以耐電痕化和電蝕損試驗進行對比的材料必須是同一種類的材料，因此不同種類材料的試驗結果對比可能并非完全有效
Electrical insulating materials.Method to evaluate the resistance to tracking and erosion.Rotating wheel dip test
方法確定固體絕緣材料的耐電痕化指數和比較跟蹤指數
Method for the determination of the proof and the comparative tracking indices of solid insulating materials
本標準提出了在工頻(45 Hz~65 Hz)下,用液體污染物和斜面試樣,通過耐電痕化和蝕損測量評定在嚴酷環境條件下使用電氣絕緣材料的兩種試驗方法。方法1:恒定電痕化電壓法;方法2:逐級電痕化電壓法
Electrical insulating materials used under severe ambient conditions.Test methods for evaluating resistance to tracking and erosion
This standard describes two test methods for the evaluation of electrical insulating materials for use under severe ambient conditions at power
Electrical insulating materials used under severe ambient conditions – Test methods for evaluating resistance to tracking and erosion
ENGLISH This document describes two test methods for the evaluation of electrical insulating materials for use under severe
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion
Indicates relative resistance of solid electrical insulating materials to tracking for voltages up to 600 V when the surface is exposed under electric
Method of test for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
