共找到 150 條與 相對漏氣率 相關的標準，共 10 頁
本標準規定了高壓開關設備六氟化硫氣體密封的術語和定義、試驗項目及試驗方法。 本標準規定的試驗方法用以測定開關設備/隔室的相對年漏氣率。 本標準適用于以六氟化硫氣體作為絕緣和/或滅弧介質的高壓開關設備的氣體密封試驗。 注：以其他氣體作為操作、絕緣和/或滅弧介質的高壓開關設備或其他電氣設備（例如六氟化硫
Test method of SF6 gas tightness for high—voltage switchgear
本標準規定了測定氣水相對滲透率的基本原理、測定方法、資料處理和報告格式。 本標準包括穩態法和非穩態法兩種測定方法。穩態法適用于測定滲透率范圍為(0.500～1000)×10^(-3)μm^(2)的圓柱狀巖樣的氣水相對滲透率；非穩態法適用于測定滲透率大于0.0100×10^(-3)μm^(2
Gas-water relative permeability measurement
1.1 This practice describes a method for direct sampling and analysis of process vents for volatile organic compound (VOC) vapors and permanent
Standard Practice for Sampling of Process Vents With a Portable Gas Chromatograph
本標準適用于避雷器的密封試驗的技術要求和試驗方法等內容。 本標準規定了金屬氧化物避雷器（簡稱為避雷器）的密封試驗。 本標準不排斥其他有效的方法
Sealing tests of surge arresters
GB/T 4511的本部分規定了焦炭真相對密度測定和焦炭假相對密度及氣孔率測定的術語、原理、試驗步驟、結果計算、精密度等。 本部分適用于焦炭的真、假相對密度及氣孔率的測定
Coke.Determination of true relative density apparent relative density and porosity
Leakage rate testing method for facepieces of respirstors
本標準規定了非穩態恒壓法測定油氣相對滲透率的方法和要求。 本標準適用于砂巖儲層巖樣空氣滲透率大于5×10^(-3)μm^(2)的油氣相對滲透測定
Unsteady-state oil-gas relative permeability measurement
Unsteady-state determination method of coalbed methane-water two-phase relative permeability
High-speed determination of true relative density,apparentrelative density and porosity of coke for export
This standard specifies the maximum leakage rates allowed for equipment used in welding,cutting,and allied processes. It applies only to individual
Maximum leakage rates (gas tightness) of equipment used for welding, cutting, and allied processes
5.1 Use of this guide can be beneficial in determining
Standard Guide for Evaluating the Relative Effectiveness of Building Systems to Resist the Passage of Products of Combustion Based on the Aggregation of Leakage Rates
Distribution System Leakage Impacts on Apartment Building Ventilation Rates
Calibration methods for standard leaks versus calibration methods
Integral leakage rate test of Containment with the absolute pressure methodDiese Norm ist wortgleich mit der KTA-Regel 3405. Die KTA-Regel wurde im
Integral leakage rate test of containment with the absolute pressure method
5.1 Design calculations for radio frequency (RF
Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Coaxial Air Line
