共找到 150 條與 芯 相關的標準，共 10 頁
智能水平分型冷芯盒制芯中心主要技術包括精度要求、智能化系統、結構性能、安全與防護、液壓潤滑氣動系統、電氣系統、空運轉、負荷運轉等內容
Intelligent horizontal parting cold core box core making center
AS2553 Lock Plunger
Cable core
本文件規定了EFD磁芯的要求、試驗方法、檢驗規則、標志、包裝、運輸、貯存。 本文件適用于EFD磁芯的生產要求
EFD core
AS/NZS ISO 18274:2023 identically adopts ISO 18274:2023, which specifies requirements for classification of solid wire electrodes, solid strip
Welding consumables — Solid wire electrodes, solid strip electrodes, solid wires and solid rods for fusion welding of nickel and nickel alloys — Classification
EN 50306-3 specifies requirements for, and constructions and dimensions of, multicore cables, rated 300 V to earth, of the following type: Screened
Railway applications - Railway rolling stock cables having special fire performance - Thin wall - Single core and multicore cables (pairs, triples and quads) screened and thin wall sheathed
本標準適用于住宅、辦公室以及其他環境中的門、窗和家具上的閉鎖芯
Locking core
本標準規定了圓柱形、管形及螺紋磁芯磁性能的測量方法，該方法就是在一規定線圈內放入試驗磁芯并使磁芯位于相對該線圈的某個規定位置上，通過測量該線圈的電感量L和品質因數Q來測定磁芯的磁性能。 試驗時，一般用對照標準磁芯作相對測量來評定磁芯。 本標準包括的磁芯，長度不入于45mm，直徑
Measuring methods for cylinder cores,tube cores and screw cores made of magnetic oxides
Core shooter
cored wire
CONNECTOR, PLUG, TYPE I, MOLDED, THREE-, FOUR-, & FIVE-CONDUCTOR (SUPERSEDING MIL-C-24231/1C)
模具最大尺寸：700X400X350mm 射砂最大質量：20kg 模板之間最大開檔距離：710mm 模板之間最小開檔距離：150mm 合模行程：285+285mm
Core shooter
This standard corresponds to a proposal prepared by ISO/TC82/WG5. When the result of the ISO work is available a revision of this standard may
Core drilling equipment Double-tube core barrels, type T. Bortom-discharge and swivel type Core lifters
Draft IEC 1156: generic specification for multicore and symmetrical pair/quad cables for digital communications
This standard corresponds to a proposal prepared by ISO/TC82/WG5. When the result of the ISO work is available a revision of this standard may
Core drilling equipment Double-tube core barrels, type T. Bottom-discharge and swivel type Core-lifter cases
