共找到 150 條與 鎳及鎳合金棒材 相關的標準，共 10 頁
This part of EN 754 specifies the mechanical property limits applicable to aluminium and aluminium alloy cold drawn rod/bar and tube. Temper
Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 2: Mechanical properties
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T
Copper and copper alloys — Profiles and bars for general purposes
Copper and copper alloys - Profiles and bars for general purposes
1.1 This specification covers three grades of zirconium and zirconium alloy bar and wire.1.2 Unless a single unit is used, for example
Standard Specification for Zirconium and Zirconium Alloy Bar and Wire
1.1 This specification2 covers three grades of zirconium and zirconium alloy bar and wire. 1.2 Unless a single unit is used, for example corrosion
Standard Specification for Zirconium and Zirconium Alloy Bar and Wire
Copper and copper alloys - Profiles and bars for general purposes
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire
本規范涵蓋了一種鉭合金，其形式為棒材和桿材，最大直徑不超過3.5英寸（88.9毫米）。主要適用于需要暴露在超高溫環境中的零件。在氧化氣氛中使用時，需要保護涂層
Tantalum Alloy, Bars and Rods 90Ta - 10W
Copper and copper alloys - Profiles and bars for general purposes.
This specification covers established manufacturing tolerances applicable to bars, rods, and wire of nickel, nickel alloy, and cobalt alloys ordered
Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire
Rods,bars and forgings of titanium alloys
This specification covers a tantalum alloy in the form of bars and rods
Tantalum Alloy, Bars and Rods 90Ta - 10W
本文件描述了銅及銅合金棒材的超聲檢測方法，內容包括方法原理、一般要求、儀器設備、檢測類型選取、對比試塊、檢測步驟、缺陷評定、質量等級、檢測報告。適用于A型脈沖縱波反射法對直徑不小于10 mm的圓形、矩形、方形和正六邊形銅及銅合金棒材（以下簡稱“棒材”）的超聲檢測
Ultrasonic testing method for copper and copper alloy rods
Draft Document - Titanium and titanium alloy bars - Technical specification
本規范規定了裸鎳和鎳合金焊條、帶焊條和焊棒的分類要求。它包括鎳含量超過任何其他元素的成分。 本規范同時使用美國習慣單位和國際單位制（SI）。測量不是精確的等價物；因此，在引用材料屬性時，每個系統必須獨立使用，不得以任何方式組合。帶A5.14名稱的規范使用美國習慣單位。A5.14M規范使用SI單位
Specifications for nickel and nickel alloy bare welding rods and bars
