IEEE 2780-2019 絕緣穿刺連接器的 IEEE 標準

本標準定義并描述了用于架空絕緣電纜線路、橋梁和涵洞、廊道、隧道、礦山、電纜井等場所，額定電壓不超過12 kV的絕緣穿刺連接器（IPCs）的技術要求、測試、檢驗規則、標志和包裝。 1.2 目的 本標準的目的是支持使用IPCs部署架空絕緣電纜。本標準能夠降低部署架空絕緣電纜的成本并擴大市場適用性

IEEE Standard for Insulation-Piercing Connectors

IEEE Std 2780-2019 絕緣穿刺連接器的 IEEE 標準

本標準定義并描述了用于額定電壓高達12 kV的架空絕緣電纜線路、橋梁和涵洞、廊道、隧道、礦井、電纜井等的絕緣穿刺連接器（IPCs）的技術要求、測試、檢驗規則、標志和包裝。 本標準的目的是支持使用IPCs部署架空絕緣電纜。本標準降低了架空絕緣電纜部署的成本并擴大了市場適用性

IEEE Standard for Insulation-Piercing Connectors

IEEE P2780/D7.0-2018 絕緣穿刺連接器標準草案

This standard defines and describes the technical requirements@ tests@ inspection rules@ sign and package of insulation piercing connector used

Draft Standard for Insulation Piercing Connectors

AS/NZS 4396(Int):1996 連接器 絕緣穿刺 用于 0.6/kV 架空成束電纜

Connectors - Insulation piercing - For 0.6/kV aerial bundled cables

IEEE P2780/D7.0, September 2018 IEEE 批準的絕緣穿刺連接器標準草案

The technical requirements, tests, inspection rules, sign, and package of insulation-piercing connector used in aerial insulated cable lines, bridges

IEEE Approved Draft Standard for Insulation Piercing Connectors

DL/T 1190-2023 絕緣穿刺線夾

本文件規定了絕緣穿刺線夾的分類及命名、技術要求、試驗方法、判定準則、標志、包裝、運輸和貯存等要求。 本文件適用于額定電壓20kV及以下架空線路、橋涵、隧道、礦道、電纜管井絕緣電纜的絕緣穿刺類線夾

Insulation piercing clamp

AS/NZS 4396:1999 連接器．絕緣刺穿．用于0.6/1kV高空捆扎電纜

Specifies requirements for the construction and performance of insulation piercing connectors between 0.6/1 kV aerial bundled cables and insulated

Connectors - Insulation piercing - For 0.6/1 kV aerial bundled cables

BS EN IEC 60352-6:2022 無焊連接 絕緣刺穿連接 一般要求、測試方法和實踐指導

1???Scope This part of IEC?60352 is applicable to insulation piercing connections made with stranded wires and tinsel wires , insulated flat

Solderless connections. Insulation piercing connections. General requirements, test methods and practical guidance

NEMA C119.5-2018 電連接器 絕緣穿刺連接器系統 額定電壓為 600 伏或更低（低壓架空捆綁電纜和絕緣和非絕緣電線）

This Standard covers insulation piercing connectors used for making electrical connections between insulated@ insulated-to-bare@ and bare-to-bare

Electric Connectors - Insulation Piercing Connector Systems@ Rated 600 Volts or Less (Low - Voltage Aerial Bundled Cables and Insulated and Non-Insulated Line Wires)

NF C93-026*NF EN IEC 60352-6:2023 無焊連接 第6部分：絕緣穿刺連接 一般要求、試驗方法和實用指南

Solderless connections - Part 6 : insulation piercing connections - General requirements, test methods and practical guidance

KS C IEC 60352-6-2023 無焊連接 第6部分：絕緣刺穿連接 一般要求、試驗方法和實踐指南

Solderless connections－Part 6：Insulation piercing connections－General requirements, test methods and practical guidance

CEI EN 60352-6:1998 無焊連接 第6部分：絕緣穿刺連接 一般要求、試驗方法和實用指南

ENGLISH * W/D S/S BY CEI EN IEC 60352-6 La presente Norma si applica alle connessioni a foratura isolante per usi

Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance

NF EN IEC 60352-6:2023 無焊連接 - 第 6 部分：絕緣刺穿連接 - 一般要求、測試方法和實用指南

Connexions sans soudure - Partie 6 : connexions à percement d'isolant - Exigences générales, méthodes d'essai et guide pratique

UNE-EN IEC 60352-6:2023 無焊連接 第6部分：絕緣刺穿連接 一般要求、測試方法和實踐指南

Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance (Endorsed by Asociación Espa?ola de Normalización in March of 2023.)

DIN EN IEC 60352-6:2020-04 無焊連接 第6部分：絕緣刺穿連接 一般要求、測試方法和實踐指南

This part of IEC 60352 is applicable to insulation piercing connections made with stranded wires and tinsel-wire, flat conductors and flat flexible

Solderless connections - Part 6: Insulation piercing connections - General requirements, test methods and practical guidance (IEC 48B/2752/CD:2019); Text in German and English / Note: Date of issue 2020-03-20*Intended as replacement for DIN EN 60352-6 ...