共找到 144 條與 額定彎曲負荷 相關的標準，共 10 頁
La présente norme européenne définit la méthode d'essai pour déterminer la contrainte de rupture par flexion de tous les carreaux céramiques
Square bricks and ceramic panels, determination of load to fracture due to bending
La presente norma è la versione ufficiale della norma europea EN 1533 (edizione agosto 2010). La norma specifica metodi di determinazione della
Wood flooring - Determination of the bending strength under static load - Test methods
Wood flooring - Determination of bending strength under static load - Test methods
Wood flooring - Determination of bending strength under static load - Test methods
本標準規(guī)定于溫度繼續(xù)升高時，塑料（包括模造或鑄造之熱固性塑料或熱塑性塑料）或硬橡膠受任意彎曲負荷所發(fā)生任意變形時之溫度測定方法。本方法適合對在溫度升至 27℃ 時仍為硬質之物質之測定，且可應用在厚度為 3 至 4.2 mm 之模制物及厚度為 3 至 13mm 之板狀物上。但并不
Plastics and Ebonite - Determination of Temperature of Deflection Under Load
1.1 ISO 75 specifies methods for the determination of the temperature of deflection under load (flexural stress under three-point loading
Plastics - Determination of temperature of deflection under load - General test method
該文件規(guī)定了一種評估液壓缸折彎載荷的方法，具體包括： a) 考慮液壓缸的幾何模型；b) 可用于所有類型的氣缸安裝和活塞桿連接（參見表2）；c) 包括由進行計算的人設定的安全系數k，并在結果中報告該安全系數；d) 考慮可能的偏離軸心載荷；e) 考慮液壓缸重量，不忽略所有橫向力；f) 可以實施為簡單的
Hydraulic fluid power. Method for evaluating the buckling load of a hydraulic cylinder
1.1 本文件提供了塑料在負載下撓曲溫度（三點加載下的彎曲應力）測定的通用試驗方法。定義了不同類型的試樣和不同的恒定載荷以適應不同類型的材料。 1.2 ISO 75?2給出了塑料（包括填充塑料和纖維增強塑料，其中纖維長度在加工前不超過7.5毫米）和硬橡膠的具體要求，而ISO 75?3給出了高強度
Plastics. Determination of temperature of deflection under load. General test method
Plastics. Determination of temperature of deflection under load. Plastics and ebonite
Wood flooring - Determination of bending strength under static load - Test methods; German version EN 1533:2010
This European Standard specifies methods of determining the bending strength of wood and parquet flooring under static loads: a method with a static
Wood flooring - Determination of bending strength under static load - Test methods
ADOPTED_FROM:EN 1533:2010 This European Standard specifies methods of determining the bending strength of wood and parquet flooring under static
Wood flooring — Determination of bending strength under static load — Test methods
Wood flooring - Determination of bending strength under static load - Test methods
Wood flooring - Determination of bending strength under static load - Test methods
Tests on thin-walled celluloid cylinders to determine the interaction curves under combined bending, torsion, and compression or tension loads
