共找到 150 條與 裝載夾具 相關的標準，共 10 頁
Loading limit for railway double-layer container transport (temporary)
This document specifies dimensions for data media and their mounting space for tools and clamping devices and other operation equipment
Data media for tools and clamping devices; dimensions for data media and their mounting space
1 通用要求: 1.1 儀器設備 1.1.1 測試系統需要實現設定壓力（壓差）、頻率、測試溫度和循環計數功能，若需要監控其他參數，闡述使用該方法的依據。 1.1.2 壓力控制系統∶應選擇在測試頻率下能精準測量器械附近壓力的壓力傳感系統，并且壓力測量系統
Test methods for in vitro pulsatile durability testing of cardiac occluder
Clamps for jig and fixture
本文件規定了汽車輪轂裝夾夾具的要求、試驗方法、檢驗規則、標志、包裝、運輸和貯存
Automobile hub clamping fixture
This Aerospace Information Report (AIR) contains information relative to stresses and loads developed in tubes, fittings and clamps caused by tube
Clamp Loads and Bending Stresses in Aircraft Tubing Installations
The document specifies dimensions, designation, material, design and connecting dimensions for spring-loaded catches. Spring-loaded catches according
Spring-loaded catch for jigs
Clamps for jigs and fixtures
Safety requirements for cableway installations designed to carry persons - Carriers - Part 1: Grips, carrier trucks, on-board brakes, cabins, chairs, carriages, maintenance carriers, tow-hangers
Install fixture pump
This European Standard specifies the safety requirements applicable to carriers for cableway installations designed to carry persons. It is applicable
Safety requirements for cableway installations designed to carry persons - Carriers - Part 2: Slipping resistance test for grips
Safety requirements for cableway installations designed to carry persons - Carriers - Part 2: Slipping resistance test for grips
本標準是對JB 3627.9-84《組合夾具組裝用工具、輔具 鏜孔夾具檢驗棒》的修訂，僅按有關規定重新進行了編輯。 本標準規定了鏜孔夾具檢驗棒的結構尺寸、技術要求及標記。 本標準適用于12mm槽系組合夾具元件的組裝
Tools, auxiliary tools for assembling combined clamps Inspection bar for clamps for boring holes
本標準是對JB 3627.8-84《組合夾具組裝用工具、輔具 鉆孔夾具檢驗棒》的修訂，僅按有關規定重新進行了編輯。 本標準規定了鉆孔夾具檢驗棒的結構尺寸、技術要求及標記。 本標準適用于12mm槽系組合夾具元件的組裝
Tools, auxiliary tools for assembling combined clamps Inspection bar for clamps for drilling holes
Esempio e tabella con designazione. Materiale: acciaio Fe 50-1 UNI 5334-64, ovvero ghisa g 15 UNI 5007
Gripping and holding appliances. Wedge clamps.
